Full Hex Nut: We bring forth Tie/Hex Road Connector that is well acclaimed for their durability, high tensile strength and capability to withstand high temperature.
Bearing Plate Bearing Plate are key components in transferring loads from the post and top plates to the rods in a continuous rod tiedown system. Bearing plate must be designed to spread the loads across the sole plates to minimize the effects of wood crushing.
Thread Steel Bar/ Post Tensioning Bar:
We are a manufacturer and supplier of Scaffolding Tie Rod. It is used for formwork with water stop, anchor tie nut, wing nut, steel cone formwork materials and accessories and also to form tie formwork system with form tie.
We manufacture this rod, we use best quality mild steel, sourced from trusted vendors. Scaffolding Tie Rod is one of the most important accessories in pouring shear wall project. Clients can avail our rod in different sizes and specifications as per their requirements.
LIVIZA formwork tie rods have a relatively strong structure and were used for industrial and residential purposes. All formwork tie rod accessories such as tie nuts, water stoppers, steel cones and hex nuts are also available at the factory. Construction MS Tie Rod available at 12mm, 14mm, 16mm & 20mm
T-Bolt Nut+Washer Plain:
T bolt made of good quality Wire Steel. Size 1/2″x90 mm, duly white zinc plated with nut and 3 mm thick washer.
Flat Bearing Plate for Anchor Steel Bar:
Flat Plates are used for timber or steel walings in conjunction with a winged nut or a hex nut for load transfer.
Tie Rod/ Threaded Rod:
LIVIZA formwork tie rods have a relatively strong structure and were used for industrial and residential purposes. All formwork tie rod accessories such as tie nuts, water stoppers, steel cones and hex nuts are also available at the factory.
Construction MS Tie Rod available at 12mm, 14mm, 16mm & 20mm
Wing Nuts can be used as anchor nuts both for timber and steel walings. They can be fixed and loosened using a hexagon wrench or a threadbar.
LIVIZA Scaffolding, shall strive to be most reliable brand in Bangladesh for its scaffolding & formwork products with relentless focus on our quality policies.
Base Nut/ Tie Nut/ Anchor Nut Tie Rod:
Flanged Wing Nut Casting formwork tie rod anchor nut is widely used in formwork construction. Wing Nut by a larger pedestal allowing a direct bearing on walings. It can be screwed on or loosened using a hexagon wrench, threadbar or hammer.
Rapid Clamp are made of high Quality Materials
Shutter Clamp/ Column Clamp Shikanja:
We are engaged in offering topmost quality of Shuttering Clamp / Column Clamp Shikanja used for construction work. We offer Formwork Shuttering Clamps. Our wide range of shuttering clamps is used to support scaffolding at construction sites. We assure our clients with the impeccable quality of our shuttering clamps as we test our each and every clamp on various stringent quality parameters.
– Can withstand high load
– Easy installation
– Available in varied shapes and sizes
– Dimensionally accurate
– Compatible with all type of scaffoldings
Available Size: 2,2.5,3,4 feet & Thick-3-5mm
Plastic Cone/ PVC-Selves Cone/ Plastic tie rod cone
The end is Plastic Cup or Plastic Cone. And the plastic tube with two pieces of the plastic cone on the both sides also called Plastic Sleeve. It is used to protect the Tie Rod and there are some different sizes and thickness available.
– PVC Shuttering Cone
– PVC Cone For Tie Rod
– Tie Rod PVC Cone
– Tie Rod System
– PVC Sleeve Cone– Conduit Pipe
Pressed Waler Plates:
Pressed Waler Plates are used for timber or steel walings in conjunction with a winged nut or a hex nut for load transfer. The embossing of the plate increases its rigidity. Load capacity depends on the contact area, the admissible bearing pressure and the threadbar that is used.
D FORM TIE SYSTEM:
D FORM TIE SYSTEM is widely used in the construction industry, The system is easy to use , fast to assemble or remove and all parts are reusable . D Form Tie system is designed to prevent breakages in formwork and keeping concrete structure in shape. The parts include such as D Form Tie, D Cone, Inner Unit, Flat Rib Washer,Three Rib Washer, 1/2” Hex Nut, Rubber Ring etc. Our products are suitable for various applications that can be customized as per the requirements of the clients. They are made by using high grade material which is sourced from leading vendors of the market
Construction Formwork Form Tie System Form Tie and Inner:
Construction Formwork Form Rib Washer:
A turnbuckle is a piece of hardware used to eliminate slack and adjust tension in a rope, cable, or other tensioning system
©2022. Liviza Bangladesh. All Rights Reserved.